Search Results

An original multi-body dynamics simulation program for reciprocating engine system with elastically deformable piston skirt was developed in order to understand and examine the secondary motion of piston. This program uses specialized equations of motion using only the rotational degree of freedom of each components taking the valiation of rotating speed of crank into account. In order to validate the practical use of this program, the calculations were compared with the measurements on the piston motion of a two-stroke engine for motorcycles and a four-stroke engine for automobiles, and good agreements were obtained between them.

The specific output of 4-cycle engines are generally smaller than that of 2-cycle engines. Increasing engine speed is one method to improve the specific output, however, it contains some disadvantages in application. Hence, improvement in torque with the 4-cycle engine is desirable. Although torque could be improved by super-charging, it seems difficult to apply existing systems for small displacement engines due to problems of their size and cost. We have, therefore, newly developed a super-charging system named Advanced Crankcase Super Charge (hereinafter referred to as ACSC) using a crankcase as a supercharger. In this study, we made a 50cc single cylinder prototype engine with ACSC and carried out the engine unit tests and actual running tests on a scooter. From these tests, the torque that is twice as that of the naturally aspirated engine was obtained.

In the past, the performance of motorcycle engines has improved quite rapidly through intensive competition in racing and in the marketplace. Motorcycle engines have contributed to the technological progress of internal combustion engines (hereafter abbreviated as ICE). Today's environmental concerns require motorcycle engines to improve fuel economy and exhaust emission pollutants. After examination of potential measures to improve the thermal efficiency of small engines, it was concluded that if engineers of motorcycle engines fail to take on new ideas such as those being developed in cold fusion, it is foreseen that motorcycle engines will be replaced with new power plants as was seen on locomotives in the past.

In recent years, global warming, depletion of fossil fuels, and reducing pollution have become increasingly prominent issues, resulting in demand for environmentally-friendly two-wheeled vehicles capable of reducing CO2 emissions. However, it remains necessary to meet customers’ expectations by providing smaller drivetrains, lighter vehicles, and support for long-distance riding, among other characteristics. In the face of this situation, hybrid electric vehicle (HEV) systems are considered to be the most realistic method for creating environmentally-friendly powertrains and are widely used. This research introduces a hybrid electric two-wheeled vehicle fitted with an electrical variable transmission (EVT) system, a completely new type of electrical transmission that meets the aforementioned needs, achieving enhanced fuel efficiency with a compact drivetrain. The EVT system comprises double rotors installed inside the stator.

A direct injection system in which fuel was injected through the cylinder wall was developed and detailed investigation was made for the purpose of reducing short-circuit of fuel in 2-stroke engines. As a result of dynamo tests using 430cc single cylinder engine, it was found that the injector was best attached at a location as close to TDC as possible on the rear transfer port side, and that the entire amount of fuel should be injected towards the piston top surface. Emissions were worsened if fuel was injected towards the exhaust port or spark plug. Although the higher injection pressure resulted in large emissions reduction effects, it did not have a significant effect on fuel consumption. When a butterfly exhaust valve, known to be effective against irregular combustion in the light load range, was applied, it was found to lead to further reductions in HC emission and fuel consumption while also improving combustion stability.

Direct methanol fuel cell (DMFC) system is a compact lightweight system as it eliminates the need of a complex reformer unit. Moreover, since the methanol-water-solution used as fuel does not correspond to a flammable substance, it is thought that convenience is high. We have developed the hybrid scooter integrated with the DMFC system and the Li-ion rechargeable batteries, and optimized various parameters related to the performance and the efficiency. The power output of the DMFC system was adjusted to the value necessary for a constant ground run in 30 km/h of a commercial small electric scooter. All the system components had to be constituted in the limited space and under the restricted weight conditions. The net-power-output of the system was examined under various air flow rate, fuel flow rate and methanol concentration conditions.

The demands on internal combustion engines for low emissions and fuel consumption are increasing year by year. On the other hand, engines to be used in motorcycles need to provide high output and quick response to meet user desire. In order to realize low fuel consumption while keeping high performance, it is necessary to properly understand cyclic variations during combustion as well as the influence of the injection system on fuel control during transient periods. The current paper reports on the results of a study in the influence of port fuel injection on combustion stability in a small displacement motorcycle engine, using both a series of experiments and CFD. The parameters of the injection systems under study are: (1) injection targeted area, (2) injection timing, and (3) fuel droplet size. The results of the current study show that injection aimed at the upstream wall yielded the best combustion stability.

Yamaha Motor Co., Ltd. has been developing 1kW generator system of direct methanol fuel cell (DMFC). The performance and durability characterization of a 1kW DMFC stack that the weight of the stack was decreased 20% in comparison with that of previous stack was evaluated. The DMFC operation condition was optimized from the design of experiment and the results of the net output. The overall system efficiency of the Yamaha DMFC system using the stack became a maximum in current 20A, was 30%. The stack was generated at 20A under the Daily Start up and Shutdown (DSS) condition for 1500h. This report describes some latest results concerning the durability characterization, which were obtained in the NEDO's project.

A construction of the technology concerning fuel consumption improvement is an important problem not only for the four-wheeled vehicle but also for the motorcycle in recent years when petroleum resources are depleted rapidly. Yamaha originally developed a new fuel injection system (YMJET-FI) and applied the system to a single cylinder, water-cooled and small-displacement engine. In this paper, we would introduce the results of improving the fuel economy with keeping high performance. Improvements were noted in three matters, namely, in the lower load range, 1.Strengthening of in-cylinder flow, 2.Atomization of fuel spray, and 3.Reduction of wall film quantity.

MotoGP is the pinnacle of motorcycle racing, with the world's top riders racing 800cc prototype machines at leading venues around the world. The riders compete against each other to win the title and show their superiority. The manufacturers have improved the engines every year to gain high power with low-fuel consumption. The percentage of the duration in fully open throttle is less than 20% of the race, but the partial throttle is used as much as 80%. Moreover, when the rider accelerates the machine, the front tire is easy to be lifted from the ground. In the middle of corner, the rider cannot open the throttle fully because of the tire slip. Therefore, it is the most important factor to appropriately control a throttle in the partial area. The Drive-By-Wire (DBW) system is one of the solutions for the force control. The vehicle simulation in the engine dyno test helped efficiently to evaluate the DBW.

We studied the mechanism of occurrence and evaluation of the surge that is produced in motorcycles equipped with 2-stroke cycle engines by simultaneously measuring chassis behavior and combustion. When modal analysis was performed by measuring the acceleration of each chassis component while placing the test vehicle on a chassis dynamo, it was found that pitching, in which the tires serve as springs, and resonance, generated from the rear suspension spring, occurred simultaneously during surge generation. The major component that is felt physically is pitching. Although a certain degree of correlation was observed between fluctuations in combustion and occurrence of pitching, since the drive line contains a large amount of back lash, the system has a high degree of non-linearity, thus making it difficult to obtain a well-defined correlation.

The purpose of this paper is to investigate the effect of the piston shape and weight on the friction losses. The motoring test was conducted on pistons with various shapes, rigidities, and weights at 3000-16000 rpm. The test results suggested that the piston friction loss would be abruptly increased mainly because of the increase in the skirt friction caused by the change of the piston attitude. Then, the piston behavioral simulation was conducted using a two-dimensional rigid model in consideration of the skirt rigidity, which proved the above suggestion. This paper consists of the paper presented at 1990 JSAE Autumn Convention and the results of the investigation we conducted based on the calculation of piston behavioral simulation.

Laser powder bed fusion is one of the metal additive manufacturing technologies, so-called 3D printing. It has attracted great attentions due to high geometrical flexibility and remarkable metallurgical characteristics. An oil catch tank has been widely used in automotive industries for filtering oil vapors or carbon sludge from blow-by gas as a conventional usage. A pneumatic valve system mainly adopted to high-performance engines is also a potential application of it because undesirable oil infiltrates into air springs during engine operation, resulting in an excess spring pressure. This work focused on developing a lightweight oil catch tank which can be applied to a pneumatic valve system by taking advantage of additive manufacturing techniques. Al-Mg-Sc alloy powder with high tensile strength as well as high ductility were used under the consideration of specific strength, printability and availability.

In recent years, efforts to reduce CO2 emissions (carbon neutrality) have accelerated worldwide. In the aluminum manufacturing industry, CO2 emissions can be reduced by switching the raw materials of choice; from virgin ingots to recycled ingots. However, the possible characteristic change accompanying the usage of impurity-ridden recycled ingots severely limits its applications, which also limits its potential contribution to carbon neutrality. Determining how impurity elements present in recycled ingots can affect the function of manufactured components is a necessary first step towards expanding the usage of recycled ingots. In this study, we aimed to apply recycled ingots to the monolithic cylinder made of hypereutectic Al-Si alloy and investigated how impurity elements in recycled ingots affect properties (especially seizure characteristic). Die-cast cylinders using virgin and recycled ingots were manufactured and their properties were investigated.

This paper reports a methodology to estimate combustion pattern and emission by predictive simple simulation with good accuracy on various conditions of PFI engine. 3D-CFD cord VECTIS has been applied for this simulation, its settings and methods are as follows. RANS equation with liner k-epsilon model has been used as the turbulence model. Turbulent burning velocity equation contains not only turbulent velocity term but also laminar burning velocity term. For ignition model, we use a predictive model called DPIK. We iterate cycle calculation until wallfilm behavior is stabilized to get the reasonable mixture formation. We have applied this methodology to 125cc engine of motorcycle. As a result, we have obtained heat release curve and pressure curve with good accuracy on various operating conditions such as engine speed, engine load, air fuel ratio, wall temperature, and spray direction. CO and NOx calculated simultaneously have also been acceptable.

This paper reports visualization of behavior of spray, wall film, and initial flame propagation in an SI engine with port fuel injection system for motorcycle in order to directly investigate their influences on combustion and relations among them. Borescopes were used to visualize the flame propagation in the combustion chamber and wall film in the intake port. Various injection systems and injection parameters were tested: injection direction, timing, and size of droplets to investigate the effect of mixture formation. It is concluded that combustion stability under low load condition is greatly influenced by mixture inhomogeneity in the combustion chamber whose evidence is the luminous emission. It is caused by direct induction of considerable amount of liquid fuel with large size of droplets into combustion chamber or too inhomogeneous mixture in the intake port.

This paper presents a practical simulation model of the rubber V-belt CVT which is widely used as a low cost driveline element for small displacement motorcycles. The characteristic of this CVT is determined by the axial force balance between driver and driven pulleys, and the elastic force of a rubber V-belt. Because these axial and elastic forces are calculated by the kinematic and FEM analysis, a large-scale simulation model which costs long execution time for the calculation is needed to estimate the characteristic of CVT. This calculation uses the one-dimensional simulation model built up with MATLAB and SIMULINK environment, so that it was possible to get the calculation result with relatively low execution time. The elastic deformation of the rubber V-Belt was calculated by a simple spring model which was verified by experiments and FEM.

The two-stroke engines were in the main stream of the outboard motors, but they have been replaced with the four-stroke counterparts reflecting the environmental protection movement in recent years. However, the replacement with four-stroke engines involves increased number of components and additional displacement, and the outboard motors tend to be larger and heavier. This represents an issue, since the maneuverability of the boat is degraded due to the inappropriate weight distribution on the boat. Yamaha outboard motors F300B and VF250A, of which the production started in the year 2009, are equipped with four-stroke engines, and yet achieved the light weight equivalent to their two-stroke counterparts. The production volume of these models reached 20,000 units.

Recently, there have been many reports about developing control systems that actuate engines and brakes based on friction circle. We are researching the control system for motorcycles, which adds the return torque of throttle grip based on it for informing the limit of tire grip on the driving wheel. This throttle grip is a haptic display, offers haptic signals by controlling the motor connected to the throttle grip as a HMI. From the results of riding tests, the system was found helpful for riders to control the throttle grip as well as feeling easy about knowing the limit of tire grip. But it is known that the friction circle of a driving wheel depends on the normal force which changes by the gradient of road, acceleration and so on. The compensated control for changing the normal force by gradient was made to improve the throttle grip control system.

Recently the response of the engine speed at starting has more importance than ever for quick start satisfying rider’s needs, as well as exhaust emissions. We have developed a simulation for studying engine and starter specifications, engine control algorithm and other engine control parameters. This system can be utilized to realize appropriate starting time by considering air-fuel ratio under various conditions. This paper addresses what are taken account of in our method. Examples applying this to a conventional motorcycle engine are shown.